Contents of file: CFIDEIII.ZIP
     Files                                Description
-------------   ----------------------------------------------------------------
CFIDE127E.DRVR  Apple /// CF/IDE v1.27e driver for CFFA IFC version 2.0 or later
                This driver version does not check for data ready during reading
                or writing a sector (512 bytes) from the drive.  This results in
                an improvement of approximately 1.5ms reading and 3.5ms writing
                a sector compared to the CFIDE128A.DRVR version.
CFIDE128A.DRVR  Apple /// CF/IDE v1.28a driver works with all CFFA IFC versions.
                CFFA IFC versions prior to 2.0 require a data ready check during
                reading or writing a sector from the drive.  This version has
                improvements in sector read/write times of 1.5ms/3.3ms compared
                with previous CFIDE.DRIVER versions.

                Use the Apple /// system utilities program to install and
                configure the CFIDE driver in the SOS.DRIVER file on the boot
                disk.  Each drive.CFIDE1 thru .CFIDE8 corresponds to a partition
                on the drive(s).  Set configuration byte 0 to either 0 (for
                master) or 1 (for slave) for each drive in combination with the
                partition page number (0-63).  See the DIB Configuration Table
                in the file CFideIII.txt.  Set configuration byte 1 to assign a
                partition number (0-7).  Set the .CFIDE1 drive to the slot the
                CFFA card is installed.  Recommend setting the active/inactive
                status of any unused drives (.CFIDE1 thru .CFIDE8) to inactive.

CFUTIL.INTERP   Apple /// CF/IDE Utilities Program.  This Utility program is
                intended to setup, test, and manage your CompactFlash or IDE
                drives attached to the CFFA interface card.  Rename this file
                to SOS.INTERP if installed on a boot disk or set your selector
                program to launch this file.  The CFIDE driver must be included
                in the SOS.DRIVER file on the boot disk in order for this
                program to work.

CFideIII.txt    Summary of driver and partitioning utility software features.

CFide127E.txt   CFIDE driver source for CFFA rev 2.0 and later (ASCII).
CFide128A.txt   CFIDE driver source for CFFA all revisions (ASCII).

CFutil.125.txt  CFIDE partition software source (ASCII).

CATALYST.TXT    DIB configuration bytes for Quark's .CATALYST driver



                Contents of file: CFIDEIII.SHK
     Files                                Description
-------------   ----------------------------------------------------------------
CFIDE127E.DRVR  Apple /// CF/IDE v1.27e driver for CFFA IFC version 2.0 or later

CFIDE128A.DRVR  Apple /// CF/IDE v1.28a driver works with all CFFA IFC versions.

CFUTIL.INTERP   Apple /// CF/IDE Utilities Program.

CFideIII.txt    Summary of driver and partitioning utility software features.

CFide127E.txt   CFIDE driver source for CFFA rev 2.0 and later (ASCII).
CFide128A.txt   CFIDE driver source for CFFA all revisions (ASCII).

CFutil.125.txt  CFIDE partition software source (ASCII).

CATALYST.TXT    DIB configuration bytes for Quark's .CATALYST driver



                Contents of file: CFUTIL.BOOT.SDK
     Files                                Description
-------------   ----------------------------------------------------------------
SOS.KERNEL      SOS operating system file - version 1.3
SOS.DRIVER      Console and CFide driver v1.28a
SOS.INTERP      Apple /// CF/IDE Utilities Program version 1.25
SOS.DRIVER.127E Console and CFide driver v1.27e

                This is a shrinkit archive of CF/IDE /// utility boot disk.
                Expand to a 5.25" floppy to create an Apple /// boot disk.  The
                CFide driver is configured for the CFFA card in slot 3.  Use the
                SCP on System Utilities program to change the slot you have
                inserted the CFFA card.